Install on X86

https://openwrt.org/docs/guide-user/installation/openwrt_x86

dd if=openwrt-21.02.0-x86-64-generic-ext4-combined.img bs=1M of=/dev/sdX

opkg update
opkg install lsblk parted losetup resize2fs
echo fix | parted -l ---pretend-input-tty
parted -s /dev/sda resizepart 2 100% 
losetup /dev/loop1 /dev/sda2
resize2fs -f /dev/loop1

run as Container

docker exec -it openwrt /bin/sh # vim /etc/config/network // edit ip/gw & restart

config interface 'lan'
        option type 'bridge'
        option ifname 'eth0'
        option proto 'static'
        option ipaddr '10.19.0.3'
        option netmask '255.0.0.0'
        option gateway '10.0.0.1'
        option broadcast '10.255.255.255'
        option dns '10.0.0.1'

 docker network inspect macnet

macvlan - access host

https://stackoverflow.com/questions/49600665/docker-macvlan-network-inside-container-is-not-reaching-to-its-own-host

docker network create -d macvlan -o parent=eno1 \
--subnet 192.168.1.0/24 \
--gateway 192.168.1.1 \
--ip-range 192.168.1.192/27 \
--aux-address 'host=192.168.1.223' \
mynet

ip link add macnet-shim link vlan.10 type macvlan  mode bridge
ip addr add 10.19.0.1/8 dev macnet-shim
ip link set macnet-shim up
ip route add 10.0.0.1/8 dev macnet-shim
ip link show macnet-shim || ip link delete macnet-shim

macvlan/ipvlan: https://sreeninet.wordpress.com/2016/05/29/docker-macvlan-and-ipvlan-network-plugins/

ipvlan

https://docs.docker.com/network/ipvlan/#ipvlan-l2-mode-example-usage

docker network  create  -d ipvlan \
    --subnet=10.0.0.0/8 \
    --gateway=10.0.0.1 \
    --ip-range=10.19.1.0/24 \
    -o ipvlan_mode=l2 \
    -o parent=vlan.10 ipvlan10_NotTested

run as VM

QEMU NIC

use e1000; rtl8139 not detected by default.
eth0 -> LAN, eth1 -> WAN, usually.

network

DSA

replace swconfig

Multiple networks (using VLANs): https://forum.openwrt.org/t/mini-tutorial-for-dsa-network-config/96998

/etc/config/

https://openwrt.org/docs/guide-user/network/network_configuration#example_configuration

    config interface 'wan'
        option ifname 'eth0'
        option proto 'dhcp'
        option 'defaultroute' '1' # if multi WAN

    config interface 'lan'
        option type 'bridge'
        option ifname 'eth1 eth2'
        option proto 'static'
        option ipaddr '192.168.99.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

/etc/init.d/network restart

# Soft network reload
service network reload

# Hard network restart
service network restart

H/W Router: wireless interfaces may be added to lan automatically via LUCI, create new for other bridges.

QoS

SQM

https://openwrt.org/docs/guide-user/network/traffic-shaping/start

https://openwrt.org/docs/guide-user/network/traffic-shaping/sqm - Interface name to your internet (WAN) link - Link Layer Adaptation: https://openwrt.org/docs/guide-user/network/traffic-shaping/sqm-details#sqmlink_layer_adaptation_tab

nftables

https://github.com/openwrt/packages/blob/master/net/nft-qos/files/nft-qos.config

Tailscale

Mesh

iw list | grep -E "phy|mesh" # check if supported hardware

bat-adv

https://cgomesu.com/blog/Mesh-networking-openwrt-batman/#initial-configuration

opkg remove wpad-basic-
opkg install batctl-full kmod-batman-adv wpad-mesh-wolfssl

https://www.open-mesh.org/doc/batman-adv/Batman-adv-openwrt-config.html

Mode 802.11s

https://openwrt.org/docs/guide-user/network/wifi/mesh/80211s

Mode AP - 802.11r

./wireless.md#80211kvr

Switch Chip

https://openwrt.org/docs/techref/swconfig

swconfig list
swconfig dev switch0 show

VLAN 1:
        vid: 1
        ports: 0 1 6  # 6 = untagged CPU
VLAN 10:  # luci： `/network/vlan`
        vid: 10
        ports: 2 3 6t # tag CPU => create `eth0.X`(eth0=switch0) under `/network/iface_add`

https://openwrt.org/docs/guide-user/network/vlan/switch_configuration#vlan_explained_with_default_scenario_of_most_openwrt_routers - Each port untagged to exactly one VLAN ID

Bridged AP Setup

Web URI Task
/luci/admin/network/vlan + vlan : all ports tagged
/luci/admin/network/iface_add test new vlan IP ; lan : remove dhcp

Controller - OpenWISP

Compile

git clone --single-branch --branch main   --depth 1 https://github.com/openwrt/openwrt.git  /data/github/openwrt
git clone --single-branch --branch 22.03  --depth 1 https://github.com/Lienol/openwrt.git   /data/github/openwrt-Lienol-22.03
git clone --single-branch --branch master --depth 1 https://github.com/coolsnowwolf/lede    /data/github/openwrt-lede

https://hub.docker.com/r/p3terx/openwrt-build-env

docker run -itd \
    --name openwrt-build \
    -v /data/github/openwrt:/home/user/openwrt \
    p3terx/openwrt-build-env

n=openwrt-build-lede
docker exec $n sudo chown -hR user:user . && docker exec -it $n bash # tmux
cd ~/openwrt && ls -la
# make clean # rm /bin /build_dir
./scripts/feeds update -a ; ./scripts/feeds install -a
make menuconfig # make targetclean
make download -j8 V=s && make V=s -j$(($(nproc) - 1))


ls /data/github/openwrt*/bin/targets/mediatek/mt7622/*.bin -lh # host

https://openwrt.org/docs/guide-developer/toolchain/use-buildsystem

LuCI —> Applications —> luci-app-mtwifi #闭源Wi-Fi驱动 + kmod-mt76… Extra packages —> ipv6helper

Version

CONFIG_VERSIONOPT=y
CONFIG_IMAGEOPT=y
CONFIG_VERSION_DIST="##.##-SNAPSHOT"
CONFIG_VERSION_NUMBER="OpenWrt"

Mi

Hardware

Model SoC CPU MHz Flash MB RAM MB Wireless firmware Switch
CT3003 mt7981 ? 128 256 MT7981 ? MT7531AE
AX3200 / AX6S MediaTek MT7622B 1350 128NAND 256 MT7622B/MT7915E 30720KiB MT7531BE
RM AX6 Qualcomm IPQ8071A 4C A53 1.4GHz 128 MiB 512
RM AX3000 Qualcomm IPQ5000 2C A53 1.,0GHz 128 MiB 256

ImmortalWrt